In <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/products?category=227&amp;manufacturerItems=3">ICP-OES</a> analysis, maintaining reliable accuracy and precision over time can be challenging. Instrument drift, matrix effects, and fluctuations in sample introduction can all influence analytical results. One of the most effective tools to monitor and compensate for these influences is the internal standard (ISTD). When properly selected and implemented, an internal standard significantly strengthens quality assurance and increases confidence in analytical data.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Thermo_Fisher_Scientific_Internal_Standards_in_ICP_OES_A_Practical_Guide_to_Better_Accuracy_and_Precision_50d02d62c8.jpg" alt="Thermo Fisher Scientific Internal Standards in ICP-OES A Practical Guide to Better Accuracy and Precision" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Thermo_Fisher_Scientific_Internal_Standards_in_ICP_OES_A_Practical_Guide_to_Better_Accuracy_and_Precision_50d02d62c8.jpg 245w," sizes="100vw" width="1024" height="512">An internal standard is a suitable element that is added at a constant concentration to all blanks, calibration standards, quality control samples, and unknown samples. It is measured simultaneously with the analytes of interest and serves as an indicator of what is happening during the measurement process. Because it behaves similarly to the analytes in the plasma, it reflects variations that occur during sample transport, excitation, or detection.However, not every element qualifies as a good internal standard. Ideally, the chosen element should not be present in the sample, or only in negligible amounts. It must not cause spectral interferences with the analytes, and its emission line should remain free from interference itself. The internal standard should also be compatible with the sample matrix and exhibit similar excitation and ionization characteristics to the analytes. In practice, the internal standard is typically introduced at a concentration of approximately 1 to 5 ppm at the nebulizer, ensuring a clean and stable signal.When correctly applied, internal standards help correct for several types of variation. They compensate for changes in sample transport caused by pump instability or nebulizer fluctuations. They correct for plasma instability and optical drift over time. They also address certain matrix-related effects, such as changes in viscosity or surface tension that influence aerosol formation and excitation efficiency. By normalizing the analyte signal to the internal standard signal, many physical and instrumental variations can be effectively minimized.It is important to understand, however, what internal standards cannot correct. They do not resolve spectral overlaps or interferences. They cannot compensate for incorrect calibration or non-linear response behavior. Detector saturation and fundamental method errors also remain unaffected by internal standard correction. In other words, an internal standard enhances a well-designed method but cannot rescue a flawed one.Internal standards are particularly valuable in long analytical sequences, where system drift can gradually affect results. By continuously monitoring the internal standard signal, laboratories can detect and correct drift in real time. They are also helpful in sequences involving strongly varying sample matrices. Differences in density or viscosity between samples can influence transport efficiency, and the internal standard provides a way to monitor and partially compensate for these effects.Another important application of internal standards is in high-precision analysis. In precious metal determinations, for example, internal drift correction can be applied to each individual measurement. When combined with a bracketing approach, this technique can dramatically improve overall precision. In one example presented, a total precision of 0.07% over twelve measurements was achieved despite variability in individual readings. Such performance illustrates the strength of internal standard correction when precision requirements are demanding.There are two main approaches to introducing the internal standard into the ICP-OES system. In the classical approach, all blanks, standards, quality controls, and samples are spiked with the internal standard prior to measurement. This method requires careful preparation to ensure consistent concentration across all solutions. Alternatively, the internal standard can be added online during measurement using a Y-connector. In this configuration, the internal standard solution is continuously mixed with each sample as it is introduced into the nebulizer. While this method simplifies preparation and reduces the risk of spiking errors, it introduces a dilution factor that must be considered.Practical examples show that correct implementation is crucial. Poor sample homogenization can lead to incorrect internal standard correction, particularly in challenging matrices such as mineral oils. If the sample is not homogeneous, the internal standard may not reflect the true behavior of the analytes, leading to misleading corrections. Therefore, careful sample preparation remains essential, even when internal standards are used.Internal standards also play a valuable role during method development. When establishing a new method, the internal standard can be used to verify matrix compatibility and recovery. Recovery tests with certified reference materials help determine whether matrix adaptation is necessary. If recovery is not satisfactory, matrix matching can be optimized through dilution strategies or calibration adjustments. Tools such as SemiQuant in<a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/products/1489"> Qtegra software</a> can assist in identifying matrix components and guiding method optimization. Even if the internal standard is later omitted in routine operation, its use during development provides valuable insight into method robustness.It is worth noting that Argon, which is always present in the plasma, can act as a kind of “pseudo-internal standard”. While it does not replace a true internal standard element, monitoring the argon signal can provide useful information about plasma stability.In summary, internal standards are powerful tools for improving analytical reliability in ICP-OES. They help monitor and correct drift, improve precision, and increase confidence in results, especially in complex or variable matrices. However, they must be carefully selected, properly implemented, and understood in terms of their limitations. Used thoughtfully, internal standards strengthen both routine analysis and method development, contributing to consistent and trustworthy laboratory performance.<h3>Acknowledgement</h3>I would like to thank Dr. Torben Stichel, Dr. Joerg Axthelm and Dr. Sebastian Voelker Field Applications Scientist, Germany, Trace Elemental Analysis and for the support on this blog and the webinars.<h4>Sign up for our webinars live and on demand</h4><h5>English</h5><ul><li><a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/webinar/5795">Lunch and Learn Tips and Tricks Series: Qtegra Part 1</a></li><li><a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/webinar/5976">Lunch and Learn Tips and Tricks Series: Qtegra Part 2</a></li><li><a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/webinar/5977">Lunch and Learn Tips and Tricks Series: Trace Elemental Analysis (ICP-OES &amp; ICP-MS)</a></li><li><a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/webinar/5978">Trace Elemental Analysis: Ask the Expert</a></li></ul><h5>Deutsch</h5><ul><li>19. März 2026 <a target="_blank" rel="noopener noreferrer" href="https://event.on24.com/wcc/r/5179134/393E071E3B501943730958BA6203F477">Interne Standards in der ICP-OES: Ein Praxisguide für zuverlässige Qualitätssicherung im Labor</a></li><li>18. Juni 2026 <a target="_blank" rel="noopener noreferrer" href="https://event.on24.com/wcc/r/5179292/AE4C576B6A54D1AC182F7F77573D380F">Fehler reduzieren, Durchsatz steigern: Autoverdünnung mit PrepFast am ICP-MS</a></li><li>17. September 2026 <a target="_blank" rel="noopener noreferrer" href="https://event.on24.com/wcc/r/5179423/B5019C560431BADCA2A76E54E4EFE56F">ICP-OES smarter nutzen: Probendurchsatz erhöhen, Ressourcen sparen</a></li><li>17. Dezember 2026 <a target="_blank" rel="noopener noreferrer" href="https://event.on24.com/wcc/r/5179530/94EEDD1F56138F5EEE2AF24E29E6C12A">Qtegra ISDS Software Unlocked – Live im Expertengespräch</a></li></ul>Visit us on&nbsp;<a target="_blank" rel="noopener noreferrer" href="https://www.linkedin.com/showcase/72003132/admin/dashboard/">LinkedIn:</a>&nbsp;#ICP_OES #InternalStandards #ElementalAnalysis #TraceElementAnalysis<blockquote><h5>Petra Gerhards</h5>Petra Gerhards, Dipl-Ing, is Regional Marketing Manager of GC and GC-MS for EMEA at Thermo Fisher Scientific. She has more than 29 years of experience in the fields of GC-MS, SPE and LC-MS. Since joining the regional team she has contributed to workflow solutions combining vials and closures with SPE solutions, GC-MS and LC-MS. She works with KOL's on data for regional specific marketing campaigns, organizes in-house seminars and works on customer specific solutions. Her main expertise is in the field of doping and drugs-of-abuse analysis.</blockquote>

Internal Standards in ICP-OES: A Practical Guide to Better Accuracy and Precision

Our Library never stops expanding. What are the most recent contributions to LabRulezICPMS Library in the week of 6th April 2026? Check out new documents from the field of spectroscopy/spectrometry and related techniques!<blockquote>👉 <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library">SEARCH THE LARGEST REPOSITORY OF DOCUMENTS ABOUT SPECTROSCOPY/SPECTROMETRY RELATED TECHNIQUES</a></blockquote><blockquote>👉 Need info about different analytical techniques? Peek into <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library">LabRulezLCMS</a> or <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library">LabRulezGCMS</a> libraries.</blockquote>This week we bring you application notes by Metrohm, Shimadzu, Thermo Fisher Scientific and Waters Corporation!<h3>1. Metrohm: Whey permeate analysis with NIRS</h3>Monitor dairy production processes easily in seconds<ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_nir_144_download_34598659f1.pdf">Full PDF for download</a></li></ul>Whey permeate, a byproduct of manufacturing whey protein powder, contains high amounts of lactose, phosphate, and minerals. Because of its sweet and mild taste, whey permeate is often used in bakeries and chocolate manufacturing. The key to optimizing whey permeate production is to control production streams in real time. It is important to monitor the production process with highthroughput analytical techniques to maximize product yield and ensure high product quality.&nbsp;Nearinfrared spectroscopy (NIRS) is a fast, and chemicalfree analysis technique that can support this kind of testing. NIR spectroscopy can measure the most important quality parameters (i.e., protein, lactose, moisture, ash, pH, and phosphate) simultaneously in whey permeate without any sample preparation. The NIRS solution is fast, easy to operate, and can be used atline or offline in a quality control lab.<h4>EXPERIMENTAL EQUIPMENT&nbsp;</h4>158 whey permeate samples were analyzed on a <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library?mainauthorItems=220&amp;search=NIR+analyzer">Metrohm NIR Analyzer</a> equipped with a small cup accessory. All measurements were performed in reflection mode (1000–2250 nm). Metrohm software was used for data acquisition and prediction model development.<h4>CONCLUSION&nbsp;</h4>This Application Note demonstrates the feasibility of using NIR spectroscopy for whey permeate quality control. Near infrared-spectroscopy is a rapid, nondestructive analytical technique that can monitor the production process of dairy products. Aside from the analysis of whey permeate, the whey protein production stream can also be monitored by NIRS.<h3>2. Shimadzu: Measurement of Residual Metal Catalysts by X-ray Fluorescence</h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_01_01086_en_4beb25fd1d.pdf">Full PDF for download</a></li></ul><h4>User Benefits</h4><ul><li><a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library?mainauthorItems=1&amp;search=ALTRACE">ALTRACE</a> can determine levels of heavy metals present in organic compounds at around 1 mg/kg in under 10 minutes per sample.</li><li>Analyzing and managing levels of residual metal catalysts can be performed by simply placing samples in the sample vessel and analyzing them without the need for complex sample pretreatment.</li><li>By increasing the X-ray tube power and optimizing the optical design, the sensitivity of ALTRACE for heavy metals has been dramatically improved compared to the previous model.</li></ul>Many industrial products we encounter every day are produced from organic compounds by manufacturing processes that utilize a range ofsynthesisreactions and metal catalysts. Catalysis can be classified as either homogeneous or heterogeneous (although drug and chemical production processes typically use homogeneous catalytic systems). While homogeneous catalysis allows for precise control over catalytic reactions, recovering the catalyst after the reaction can be difficult.&nbsp;Nevertheless, managing the levels of residual catalysts in industrial products is critical to ensure safety and because of their high costs. For example, the ICH Q3D Guideline for Elemental Impurities (adopted in April 2017) requires risk assessments when materials such as metal catalysts are added intentionally during a production process.&nbsp;Energy dispersive X-ray fluorescence (EDXRF) spectrometry offers a simple but effective technique for assessing the levels of residual metal catalysts. Normally, the lower limit of quantification for EDXRF spectrometric analysis of heavy metals is above 1 mg/kg, which limitsits use in quantitative analysis. However, the <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library?mainauthorItems=1&amp;search=ALTRACE">ALTRACE</a> is equipped with a high-power X-ray tube that dramatically improves its sensitivity for heavy metals, enabling their determination at 1 mg/kg and below in lessthan 10 minutes. This Application News describes using ALTRACE to determine residual levels of a homogeneous catalyst after a synthesis reaction. The catalyst used in this analysis is palladium (Pd), which is a widely applied heavy metal catalyst, and the reaction catalyzed by the Pd catalyst is a cross-coupling reaction. A metal scavenger and activated carbon were each used to remove the Pd catalyst from the reaction products. Metal scavengers are frequently used in this role, and activated carbon offers a relatively cheap method for removing catalysts.<h4>Conclusion&nbsp;</h4>Common methods of elemental impurity analysis, such as atomic absorption spectrometry (AAS), ICP atomic emission spectroscopy (ICP-AES), and ICP mass spectrometry (ICP-MS), require liquid samples, so solid and powder samples must be prepared into a solution prior to analysis. However, EDXRF spectrometry can determine levels of elemental impurities regardless of the sample phase or form (solution, powder, etc.), provided the target element is distributed uniformly throughout the sample. The sensitivity of ALTRACE for heavy metals has been substantially improved compared to previous models, allowing for rapid quantitative determination of heavy metals at 1 mg/kg and below. Based on the performance presented in this article, ALTRACE is an effective tool for managing residual levels of metal catalysts.<h3>3. Thermo Fisher Scientific: The Raman Spectroscopy of Graphene and the Determination of Layer Thickness</h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/labrulez-bucket-strapi-h3hsga3/raman_spectroscopy_graphene_determination_layer_thickness_an52252_29274e8aea.pdf">Full PDF for download</a></li></ul>Currently, a tremendous amount of study is being directed toward graphene. This interest is driven by the novel properties that graphene possesses and its potential use in a variety of application areas that include but are not limited to electronics, heat transfer, bio-sensing, membrane technology, battery technology and advanced composites. Graphene exists as a transparent two-dimensional network of carbon atoms. It can exist as a single atomic-layer thick material, or it can be readily stacked to form stable, moderately thick samples containing millions of layers—a form generally referred to as graphite. However, the interesting properties exhibited by graphene (substantial electrical and thermal conductivity, high mechanical strength, and high optical transparency) are only observed for graphene films that contain only one or a few layers. Therefore, developing technologies and devices based upon graphene’s unusual properties requires accurate determination of the layer thickness for materials under investigation. Raman spectroscopy can be employed to provide a fast, non-destructive means of determining layer thickness for graphene thin films.<h4>Instrument considerations&nbsp;</h4>There are a few specifications that should be considered when selecting a Raman instrument for graphene characterization. First, since graphene samples are usually very small, selecting a Raman instrument with microscopy capabilities is imperative.The next issue to consider is which excitation laser to select. While graphene measurements can be made successfully with any of the readily available Raman lasers, it is also important to consider the substrate that the graphene will be deposited onto. It is common for graphene to be deposited on on either Si or SiO2 substrates, and both of these materials can exhibit fluorescence with near-infrared (NIR) lasers such as 780 nm or 785 nm. For this reason, visible lasers are usually recommended, typically a 633 nm or 532 nm laser.&nbsp;Next, since relatively small wavenumber shifts can significantly impact the interpretation of the Raman spectra, it is crucial to have a robust wavelength calibration across the entire spectrum. Using a single point wavelength calibration with some other applications may be sufficient, but this only ensures that one wavelength is calibrated and leaves room for a large margin of error. A multipoint wavelength calibration that is regularly refreshed, such as the standard calibration routine used with <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/products?category=184&amp;manufacturerItems=3&amp;search=dxr3">Thermo Scientific DXR3 Raman instruments</a>, will provide considerably more confidence in the results. It is also necessary to have an instrument with high wavenumber precision to observe small wavenumber shifts when altering the sample. In fact, small wavenumber shifts can represent changes in the sample rather than represent the variability from the instrument. There is a common myth that it is necessary to utilize high resolution in order to achieve high wavenumber precision. Not only is this incorrect, but a high resolution will actually add considerable noise to the spectrum, which will add to the wavenumber variability. A high degree of wavenumber precision, such as that provided by the <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/products/2239">Thermo Scientific™ DXR™3 Raman Microscope</a>, will significantly improve data confidence even when you are evaluating band shifts from low levels of strain or doping. It is also important to have exact control of your laser power at the sample and be able to adjust that laser power in small increments. This is important to control temperature-related effects and to provide flexibility to maximize Raman signal while still avoiding sample heating or damage from the laser. The DXR3 Raman systems are equipped with a unique device called a laser power regulator, which maintains laser power with unprecedented accuracy and provides exceptional ability to fine-tune laser power and optimize it for each experiment.1&nbsp;Lastly, the Raman microscope must have an automated stage and associated software to generate detailed Raman point maps. As will be seen in the next section, Raman point mapping or imaging extends the single point measurement to assess a sample’s layer thickness uniformity. The Thermo Scientific OMNIC™ Software suite contains powerful mapping and processing tools that diminish the complexity of collecting highly detailed maps and interpreting their results.<h4>Conclusions&nbsp;</h4>Raman spectroscopy is an excellent tool for the characterization of graphene and layer thickness. Few techniques will provide as much information about the structure of graphene samples as Raman spectroscopy, and any lab doing graphene characterization without Raman would be at a significant disadvantage. The DXR3 Raman Microscope is an ideal Raman instrument for graphene characterization because it can provide the high level of stability, control, and sensitivity needed to produce confident results.<h3>4. Waters Corporation: See What’s Really in Your Formulation with Backgrounded Membrane Imaging</h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/labrulez-bucket-strapi-h3hsga3/720009098_en_5d36d71789.pdf">Full PDF for download</a></li></ul>Protein aggregation in therapeutic protein products can induce adverse immunogenic responses in patients1–4 . Per the FDA’s recommendations, “strategies to minimize aggregate formation should be developed as early as feasible in product development”5 and “an assessment should be made of the range and levels of subvisible particles (2–10 µm) present in therapeutic protein products initially and over the course of the shelf life”.5 Yet, accurate subvisible protein aggregation analysis has remained elusive to protein drug formulators since current subvisible analyzers are not sensitive enough to measure protein aggregates effectively. In this application note, we explore how backgrounded membrane imaging (BMI), a high refractive index contrast technique used by the HORIZON particle analysis system, performs highly sensitive measurements of subvisible protein aggregates in the 2 µm–4 mm size range, enabling 30% higher reproducibility compared to flow imaging.<h4>Conclusion&nbsp;</h4>When studying the impact of protein aggregate refractive index, IgG protein aggregates analyzed on both the <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library?mainauthorItems=5&amp;search=HORIZON">HORIZON® instrument</a> and flow imager systems produced equivalent particle count trends. However, the HORIZON® system was more sensitive (measured more overall counts) and had overall lower variability with average CVs of 14.4% compared to the flow imager which produced average CVs of 20.1%. The differences in variability and counts were most pronounced at lower concentrations and size range respectively. Given that most particles in a therapeutic drug formulation are small, the inability of flow imagers to accurately count the smallest of protein aggregates has a dramatic impact on the total number of particles measured. This can mean an undercounting by as much as 3–10X depending on the protein and formulation conditions.&nbsp;High variability at low concentrations in flow imagers can pose a hurdle for early stage analysis were sample is scarce. In low volume analysis (&lt;250 µL), the possibility of measuring fewer particles increases, therefore it is imperative to have high sensitivity measurements when already challenged by low sampling statistics.&nbsp;In the excipient effect study, sucrose did not have an impact on the overall particle counts when measured using the HORIZON® system. This contrasts with previous studies comparing excipient effects on three flow imagers.10 In each case, the particle counts decreased up to 30% or more using standard sucrose formulation concentrations of 0–20%. The difference between the data generated by BMI and FI can be attributed to the fact that the HORIZON® instrument is not affected by particle or solution refractive index.&nbsp;Flow imagers are deeply vulnerable to the impact of refractive index when measuring protein aggregates due to their translucency and the negative impact of surfactants. Due to this basic optical phenomenon, flow imagers can dramatically undersize and undercount particles. Finding the right tool for the job will have a critical impact on data accuracy and sensitivity. Powered with BMI, the HORIZON® system provides high refractive index contrast analysis to enable accurate, robust, and sensitive subvisible particle counting from 2 µm–4 mm in as little as 25 µL of sample and 96 samples in under 2 hours.

News from LabRulezICPMS Library - Week 15, 2026

The set of soils consist of two natural agricultural soils differing in elemental composition&nbsp;<ul><li>AN-ZP01: Heavy loam with normal analyte levels&nbsp;</li><li>AN-ZP02: Silty clay loam contaminated with some heavy metals&nbsp;</li></ul>Contents of element extractable fractions with aqua regia according to ISO 11466&nbsp;<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/ANALYTIKA_agricultural_soil_CRM_0534e68e65.jpg" alt="ANALYTIKA: Matrix CRM of agricultural soil METRANAL® CRM AN-ZP01 and AN-ZP02" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_ANALYTIKA_agricultural_soil_CRM_0534e68e65.jpg 156w," sizes="100vw" width="827" height="827"><h5>Packing:&nbsp;</h5><ul><li>50 g of powder of the respective soil with a particle size of less than 100 µm in amber glass bottle.&nbsp;</li></ul><h5>Intended use:&nbsp;</h5>This set of certified reference materials is intended primarily for use in realizing metrological traceability, validation of analytical methods and the transfer of property values to other materials of similar composition.&nbsp;<h5>Recommended analytical methods for method dependent measurements:</h5><ul><li>Flame AAS, ETA-AAS, ICP-OES, ICP-MS, AMA-254&nbsp;</li></ul><h5>Metrological traceability:&nbsp;</h5>Metrological traceability is realized by using certified calibration standards solutions for the calibration of measurement methods used (direct traceability to SI unit) and/or by simultaneous analysis of a matrix CRM (RM) of similar composition.<h5>Sample preparation (aqua regia extract according to ISO 11466):&nbsp;</h5>Weigh a 3 g (± 0.001 g) sample into a 100 ml round bottom flask. Add a small amount of water (2 to 3 ml) to obtain a slurry, then 7.5 ml of conc. HNO3 (density 1.40 g/ml). Let the mixture stand until intensive foaming ceases, then add (in several portions) 22.5 ml of conc. HCl (density 1.19 g/ml), shake the mixture manually, cover the flask with a watch glass, and let stand for 16 hours (overnight) at the laboratory temperature (20 ± 2°C). Then mount a reflux condenser (a Dimroth type or similar) of about 40 cm length on the top of the flask and boil gently under reflux for 2 hours. After cooling, rinse the condenser with 20 ml of warm (~ 50°C) dilute nitric acid (5%, v/v), the liquid being collected in the round bottom flask. Remove the condenser and filter the solution from the flask through an acid-resistant high density paper filter and collect it in a 100 ml volumetric flask (make sure in preliminary tests that a suitable filter was chosen, so that the filtrate is clear). Rinse the filter and the residue three times with 5 ml of warm (~ 50°C) dilute nitric acid (5%, v/v); allow to cool and dilute with nitric acid 5% (v/v) to the mark. Transfer immediately the solution from the volumetric flask into a clean, dry 100 ml polyethylene bottle. Realize three blanks using exactly the same analytical procedure.&nbsp;It is acceptable to realize the operation described above in a glass beaker covered with a watch glass. Minimum sample size for analysis is defined with the prescribed working procedure.&nbsp;<h5>Storing and instruction for use:&nbsp;</h5>These CRM have to be stored in original bottle and between 5-30°C (in a dark and dry place). The materials should be analysed in the "as received" state and their dry weight should be determined on non-analysed aliquots oven-dried at 105°C till the constant weight. The material in the bottle must be rehomogenized before each use by mechanical shaking of the content for 1-2 minutes. The bottle should be opened a minimum of 2 minutes after rehomogenization in order to prevent an escape of fine powder particles from the bottle into the environment and their sedimentation.&nbsp;<h5>Certified and indicative values and their uncertainties:&nbsp;</h5>The certified and indicative values of extractable element fraction are summarized in Table 1. The overall means evaluated have been given a status of certified and indicative values using the following criteria: data should be available from at least two independent analytical methods, at least 5 and 3 accepted laboratory means should be available for calculation of the overall mean for certified and indicative value, respectively. At combined uncertainties presented, the contribution of uncertainty of characterization of a particular property value is dominant.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/ANALYTIKA_Table_1_Certified_and_indicative_values_of_contents_of_element_fractions_extractable_by_f56fa06aa5.jpg" alt="ANALYTIKA: Table 1 - Certified and indicative values of contents of element fractions extractable by aqua regia in CRM AN-ZP01 and AN-ZP02 and their associated uncertainties." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_ANALYTIKA_Table_1_Certified_and_indicative_values_of_contents_of_element_fractions_extractable_by_f56fa06aa5.jpg 187w," sizes="100vw" width="998" height="835"><h5>Chemical composition of soil matrix:&nbsp;</h5>The bulk composition of CRM AN-ZP01 and AN-ZP02 is shown in Table 2. The values presented in this table are not certified, but they may be useful for considerations concerning possible interferences while determining analytes given in Table 1, and for selection of suitable decomposition procedures if destructive analytical methods are to be used.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/ANALYTIKA_Table_2_Matrix_composition_of_CRM_AN_ZP_01_and_AN_ZP_02_of_the_oxides_dry_cd1273cf9c.jpg" alt="ANALYTIKA: Table 2 Matrix composition of CRM AN-ZP01 and AN-ZP02 (% of the oxides dry weight at 105°C)" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_ANALYTIKA_Table_2_Matrix_composition_of_CRM_AN_ZP_01_and_AN_ZP_02_of_the_oxides_dry_cd1273cf9c.jpg 170w," sizes="100vw" width="883" height="811"><h5>Note:&nbsp;</h5>Detailed information about the production, homogeneity testing and characterization of these CRM are described in the Certification report, which is available on request.

Matrix CRM of agricultural soil METRANAL® CRM AN-ZP01 and AN-ZP02

Article

Product

Application

Academy

Video

A unique company dedicated to serving science helping our customers drive productivity and accelerate results. Through our premier brands – Thermo Scientific, Applied Biosystems, Invitrogen, Fisher Scientific and Unity Lab Services.

Thermo Fisher Scientific

Everything from the world of analytical chemistry in one place. We connect people in solving their problems. At Labrulez you will find all the necessary information easily, quickly and clearly. Stop searching and start finding.

LabRulez

Analytika is a Czech company that offers and produces certified reference materials (CRM) and (ultra)pure chemicals for quality control and quality assurance in laboratories, including accredited laboratories.

Our portfolio also includes pipettes and tips, digestors, PFA labware and other equipment for analytical laboratory and trace analysis.

ANALYTIKA

Separation Science

Agilent Technologies

Bruker

C&EN

Transmission Raman spectroscopy (TRS) is a variant of Raman spectroscopy which is advantageous in probing bulk content of diffusely scattering samples. Spatially offset Raman spectroscopy (SORS) is a variant of Raman spectroscopy that allows highly accurate chemical analysis of objects beneath obscuring surfaces. TRS is used in Agilent TRS100 Raman system for fast assay of tablets, capsules, and other dosage forms. SORS is used in Agilent RapID and Vaya systems for see-through barrier verification applications.
This online seminar provides a comprehensive introduction to the TRS and SORS technologies and their applications.
<blockquote>
Presenter: Yanqia Wang, PhD (Application Engineer, Molecular Spectroscopy, Agilent Technologies, Inc.)
</blockquote>
<blockquote>
Dr. Yanqia Wang started working for Agilent Technologies Inc. as a FTIR application Engineer in 2013, providing pre-&amp;post-sale application support. The products he covers from Bench-top FTIR microscopes to various Mobile FTIR spectrometers. Dr. Wang received his PhD of analytical chemistry from Duke University in 2004, doing dynamic IR spectroscopy research. Then he joined Fitzpatrick Center for Photonics at Duke University, doing Tissue Raman spectrometer instrumentation. Since 2007, Dr. Wang worked for Avery Dennison Corp. as a spectroscopist, providing molecular analytical support to the research &amp; development.
</blockquote>

Agilent Technology: Fast assay of Tablets, Capsules, and other Dosage forms using Transmission Raman Spectroscopy and SORS Raman Spectroscopy

Fast assay of Tablets, Capsules, and other Dosage forms using Transmission Raman Spectroscopy and SORS Raman Spectroscopy

This online seminar provides a comprehensive introduction to the TRS and SORS technologies and their applications.

Tablets, Capsules by Raman Spectroscopy and SORS

We will cover steps to ensure maximum stability and robustness in organic solvent analysis using proper hardware selection, optimized plasma conditions, and background correction techniques.
Neat analysis of solvents is an excellent alternative to ashing methods, which have large dilution factors that can push limits of detection too high. Data will be shared from analysis of several different solvents from kerosene to chloroform.
<blockquote>
Presenter: Greg Gilleland (Application Scientist, Agilent Technologies, Inc.)
</blockquote>
<blockquote>
Greg began his spectroscopy career in 1987 in Colorado, working at a series of environmental labs. After 14 years working in the world of commercial environmental labs, he moved on to a spectroscopy instrument manufacturer where he performed service and sales functions over the course of 11 years. He has been with Agilent Technologies, Inc., since 2012 in the role of Application Scientist for ICP-OES, MP-AES and AA products.
</blockquote>

Agilnt Technologies: Optimizing Analysis of Oils and Organic Solvents by ICPOES

Optimizing Analysis of Oils and Organic Solvents by ICPOES

Stability and robustness in organic solvent analysis using proper hardware selection, optimized plasma conditions, and background correction techniques.

Agilent Technologies Molecular Instrumentation and Applications...
<blockquote>
Presenter: Mark Fisher, PhD (Application Engineer, Molecular Spectroscopy, Agilent Technologies, Inc.)
</blockquote>
<blockquote>
Mark, an Application Scientist for Agilent Technologies, has over 30 years of experience in molecular spectroscopy. He has held roles in Agilent&#39;s UV-Vis-NIR, fluorescence, and atomic absorption product portfolios. In addition to identifying industry trends and new business needs, Mark&#39;s responsibilities include application development, pre and post-sales support, as well as acting as a customer advocate for new product and technology opportunities. Mark received his doctorate in analytical chemistry from the University of Nebraska-Lincoln.
</blockquote>

Demystifying Molecular Instrumentation and Applications

Agilent Technologies Molecular Instrumentation and Applications...

As demand for electric vehicles increases, ensuring that the batteries that power them meet the required performance in terms of charge storage capacity, lifetime and safety is critical for market acceptance. One key aspect related to battery performance is the elemental composition of the materials used, and this is also an important consideration during any subsequent disposal or recycling. Therefore, elemental analysis of samples related to battery technology is vital at all stages in the battery supply chain, including raw material extraction and refining, battery electrode material manufacturing, and end of life disposal and recycling.
This webinar will highlight the requirements of elemental analysis throughout the battery supply chain and the key role that the Thermo Scientific™ iCAP RQplus ICP-MS instruments and other elemental analysis solutions play in supporting the measurement of battery material samples. In addition, application of a new autosampler for handling sample introduction of a variety of challenging matrices will be discussed in the presentation.
By attending this presentation you will:
<ul>
<li>Learn about the requirements for elemental analysis over the life cycle of a battery</li>
<li>Discover how automated sample handling systems can support robust instrument performance when analyzing difficult samples related to battery analysis</li>
<li>Understand how updated ICP technologies can simplify your workflow and increase uptime and productivit</li>
</ul>
<blockquote>
Presenter: Simon Nelms (Sr. Manager Vertical Marketing, Industrial, Thermo Fisher Scientific)
</blockquote>
<blockquote>
Simon Nelms is a former ICP-OES and ICP-MS applications specialist who’s been part of the Thermo Fisher Scientific team for more than 20 years. He is now a Vertical Marketing Manager for the industrial sector, with a particular focus on the battery and renewable energy markets. Simon holds a BSc in Analytical Chemistry and a PhD in research involving ICP-MS method development from the University of Hull, UK.
</blockquote>
<blockquote>
Presenter: Dr Sascha Nowak (Manger of Division Analytics and Environment, Munster Electrochemical Energy Technology Centre)
</blockquote>
<blockquote>
Dr Sascha Nowak is based at the Munster Electrochemical Energy Technology center at the University of Munster, Germany. He currently focuses his research on battery technology, specifically ageing processes, electrolytes, and recycling.
</blockquote>

Pixabay/Mikes-Photography: Powering through the complexity of lithium ion battery analysis

Powering through the complexity of lithium ion battery analysis

The requirements of elemental analysis throughout the battery supply chain and the Thermo Scientific iCAP RQplus ICP-MS instruments and other EA solutions.

Powering through the complexity of lithium ion battery

Once you have prepped your samples and maintained contamination. The next step is properly tuning and setting up your ICPMS to give the best results.
<blockquote>
Presenter: Bert Woods (Application Scientist, Agilent Technologies, Inc.)
</blockquote>
<blockquote>
Joined the Agilent ICP-MS team in 2004, with previous employment in the semiconductor industry with Dominion Semiconductor (IBM/Toshiba) and Micron. Bert is a 1997 Chemistry graduate of Radford University in Virginia and an avid Washington DC Sports fan.
</blockquote>

The importance of tuning and setting up your method on your ICPMS to achieve the best detection limits

Once you have prepped your samples and maintained contamination. The next step is properly tuning and setting up your ICPMS to give the best results.

The importance of tuning and setting up your ICPMS method

IR spectroscopy is a ubiquitous analytical technique that was first used during World War II. Since that time it has undergone significant development, providing a means for the analysis of many types of samples both in the laboratory and in the field.
This session will focus on the theory of Infrared and will discuss some modern infrared analytical techniques.
<blockquote>
Presenter: Louis Tisinger, PhD (Application Engineer, Molecular Spectroscopy, Agilent Technologies, Inc.)
</blockquote>
<blockquote>
Louis (Lou) Tisinger has a Ph.D. in Analytical Chemistry from Miami University in Oxford Ohio, where his graduate research involved the study of ATR imaging and microscope performance in vibrational spectroscopy. Most of his career has been related to pre- and post-sales support of FTIR spectrometers, microscopes, imaging systems, and thermal analytical instruments, focusing on analyzing customer samples, demonstrations, post-sales training, troubleshooting, and R&amp;D.
</blockquote>

Agilent Technologies: A discussion on the Theory of FTIR

A discussion on the Theory of FTIR

This session will focus on the theory of Infrared and will discuss some modern infrared analytical techniques.

This webinar will guide you on the best practices, tools, and techniques needed to get the most reliable, verifiable insights into your optical components. Appropriate choice of technique and methodology is critical to getting the information you need to improve design, verify product performance, and accelerate manufacturing.
We will explore the subtleties of reflection and transmission measurements at normal incidence and at oblique angles, emphasizing high absorbance, optical density, linearity, and effects of incident beam collimation. We will discuss diffuse scattering measurements and automation/robotics to broaden quality assurance programs and speed up analysis. 
The webinar is relevant to developers of optics, photonics, and electro-optical or semiconductor devices such as visual displays, laser-based range detection (LiDAR), optical communications systems and light-based scientific instrumentation. Improve your understanding of the link between your desired outcomes and the spectrophotometric approaches needed to achieve those insights. 
Key Learning Objectives:
<ul>
<li>The best spectrophotometric practices to extract deeper insights into the characteristics of optical samples.</li>
<li>How to overcome the limitations of traditional spectrophotometric tools and verify outcomes.</li>
<li>Accelerating QA/QC of optics in a production environment.</li>
</ul>
Who Should Attend:
<ul>
<li>Commercial or Academic organizations in the fields of optics, photonics, electro-optical, or semiconductors</li>
<li>Laboratory Managers </li>
<li>Scientist/Staff Scientists</li>
<li>Lab Technician/Technologist</li>
<li>Analyst</li>
<li>Project Manager</li>
<li>SME Directors, Core Lab/ Facility Managers </li>
<li>Under/Post Graduate Researchers</li>
</ul>
<blockquote>
Presenter: Travis Burt (Global Product Manager – Cary UV-Vis-NIR Spectrophotometers, Agilent Technologies)
</blockquote>
<blockquote>
Presenter: Catherine Dold (Health &amp; Environment Writer, C&amp;EN Media Group)
</blockquote>

C&EN: Optimizing Optics Using Advanced Spectrophotometry

Optimizing Optics Using Advanced Spectrophotometry

This webinar will guide you on the best practices, tools, and techniques needed to get the most reliable, verifiable insights into your optical components.

There are many different applications which can be run on an UV-Vis-nir instrument. Within these applications there are a number of instrument parameters which the user can adjust to improve the quality of the data collected or use to optimize the collection time.
A discussion will be held around both available applications and pertinent instrument parameters.
<blockquote>
Presenter: Mark Fisher, PhD (Application Engineer, Molecular Spectroscopy, Agilent Technologies, Inc.)
</blockquote>
<blockquote>
Mark, an Application Scientist for Agilent Technologies, has over 30 years of experience in molecular spectroscopy. He has held roles in Agilent&#39;s UV-Vis-NIR, fluorescence, and atomic absorption product portfolios. In addition to identifying industry trends and new business needs, Mark&#39;s responsibilities include application development, pre and post-sales support, as well as acting as a customer advocate for new product and technology opportunities. Mark received his doctorate in analytical chemistry from the University of Nebraska-Lincoln.
</blockquote>

Agilent Technologies: Navigating Your Way through Parameters and Applications of an UV-Vis-nir Instrument

Navigating Your Way through Parameters and Applications of an UV-Vis-nir Instrument

A discussion will be held around both available applications and pertinent instrument parameters.

Parameters and Applications of an UV-Vis-nir Instrument

As agricultural industries key in on sustainability efforts, it’s imperative to consider how to improve upon the efficiency of our “original recycling,” rendering. The weight of serving as a recyclable industry all while enduring the costs that come with meeting guaranteed analyses is immense and requires an innovative solution to limit final product variation while reducing the fiscal and physical limitations of validating these ingredients. With FT-NIR technology, we now have a rapid method of analysis that allows for greater blending and formulation control.
In this webinar, we’ll cover applications within the rendering industry whereby FT-NIR technology expands the potential for in-process adjustments to ensure that product quality, and thus customer satisfaction, is consistently achieved.
What You’ll Learn:
<ul>
<li>How FT-NIR has found its place in the rendering industry</li>
<li>How much are traditional wet chemistry analyses really costing your facility?</li>
<li>Titration assays: How FT-NIR can reduce our dependence on this primary reference method</li>
<li>How to minimize final product variation via benchtop and inline FT-NIR instruments</li>
</ul>

Bruker: Advantageous FT-NIR Applications for the Rendering Industry

Advantageous FT-NIR Applications for the Rendering Industry

We’ll cover applications within the rendering industry whereby FT-NIR technology expands the potential for in-process adjustments to ensure that quality..

Agilent&#39;s Cary 3500 Flexible UV-VIS Spectrometer makes concentration analysis easy. Its unique hardware design allows you to effortlessly change cuvette pathlengths for switching between assays.
In this presentation, we will discuss concentration analysis workflows and how to streamline these measurements with reliable hardware and software.
<blockquote>
Presenter: Scott Melis, PhD (Application Scientist, Agilent Technologies, Inc.)
</blockquote>
<blockquote>
Scott Melis has a PHD in Physics from Georgetown University in Washington, DC and started with Agilent in 2021 as a Molecular Spectroscopy Application Scientist. In his graduate work, Scott studied nanoparticle formation and growth for a variety of applications. Projects that he worked with include developing processes to deposit and characterize semiconducting molecular nano-cocrystals for use in optoelectronic devices as well as controlling polymer nanoparticle size through rapid mixing conditions.
</blockquote>

Agilent Technologies: Simple UV-VIS Workflows For Concentration Analysis

Simple UV-VIS Workflows For Concentration Analysis

We will discuss concentration analysis workflows and how to streamline these measurements with reliable hardware and software.