An international research team, which included scientists from the Faculty of Science at Palacký University and the Institute of Physics of the Czech Academy of Sciences, has succeeded in unraveling the complex mechanism by which a chemical bond is formed during a collision between molecules. The experts found that the reaction only takes place if the molecules are oriented towards each other within a very narrow range of angles – within the so-called cone of reaction. This joint research has thus provided an answer to one of the fundamental questions of chemistry: under what conditions do chemical bonds form between molecules. The results of the study&nbsp;Spatially resolving the cone of reaction for a single molecule&nbsp;were published in the prestigious scientific journal&nbsp;Science.Many chemical reactions begin with the collision of two particles. However, for a new chemical bond to form, it is not enough for the molecules simply to come into contact. Their collision must occur with sufficient energy, in the correct relative orientation and at the right location. Under normal conditions, such as in solutions or gases, molecules collide chaotically, and the precise parameters of these collisions cannot therefore be controlled.<h4>Molecules under control</h4>Scientists were able to control the collisions of individual molecules on a copper surface and monitored the process using a scanning tunnelling microscope. They used the instrument not only to visualise individual molecules, but also to deliberately accelerate the reactants towards one another. They subsequently analysed each collision with atomic-level resolution. This enabled them to determine unequivocally whether a new chemical bond had formed between the molecules.<h5>“What is hidden in the statistics of billions of collisions in conventional chemistry, we have managed to break down into individual cases and map directly.” Adam Matěj</h5>A key finding of the study is that the outcome of a collision is determined by the extremely precise orientation of the molecules. A new bond was formed only when the target molecule was oriented within a few degrees of the direction of movement of the other molecule. When rotated by more than fifteen degrees, the molecules simply bounced off each other without any reaction.<h4>The precise orientation of the molecules is crucial</h4>“For the first time, we were able to observe, using a single molecule, exactly how precisely it must be oriented for the reaction to take place at all. What is hidden in the statistics of billions of collisions in conventional chemistry, we have managed to break down into individual cases and map directly,” said Adam Matěj from the Department of Physical Chemistry at the Faculty of Science.The theoretical part of the study, in which researchers from Palacký University and the Institute of Physics of the Czech Academy of Sciences were involved, played a significant role. Using quantum-mechanical calculations, they explained why the ‘reaction cone’ is so narrow. It turned out that the reactive carbon atom is surrounded by hydrogen atoms, which block the access of the reacting molecule from almost all directions.<h4>The arrangement of atoms restricts access to the reaction</h4>The calculations also shed light on a surprising experimental result. The chemical reaction took place even when the molecule moved along an adjacent row of copper atoms, where, according to the original assumptions, no bond should have formed.<h5>“The strength of this work lies in the fact that the experiment and theory have been brought together into a single picture. The microscope showed what happens during the collision, and the calculations explained why.” Pavel Jelínek</h5>“The explanation lies in the slight displacement of a single copper atom on the surface. The target’s bond to the surface pulls it out of its position and brings it close enough to the neighbouring row that it can literally take over the projectile and direct it to the correct spot. This shows that the surface is not merely a passive substrate, but actively participates in the reaction itself and can even facilitate pathways that would otherwise be unfavourable,” noted Adam Matěj.<h4>The surface also determines the course of the reaction</h4>The results are significant for the development of so-called surface reactions, in which new materials and nanostructures are purposefully assembled from individual molecules. A better understanding of the influence of the spatial arrangement of molecules will enable the design of molecular building blocks so that they bond more reliably and efficiently. This represents an important step towards the development of technologies based on the controlled construction of structures atom by atom.“The strength of this work lies in the fact that experiment and theory have been brought together into a single picture. The microscope showed what happens during the collision, and the calculations explained why. Without a theoretical model, we would have found it difficult to discover that the movement of a single surface atom is behind the unexpected course of the reaction,” added Pavel Jelínek from the Institute of Physics of the Czech Academy of Sciences.<blockquote>The study&nbsp;Spatially resolving the cone of reaction for a single molecule&nbsp;was produced in collaboration between researchers from the University of Graz, the Institute of Physics of the Czech Academy of Sciences, Palacký University in Olomouc, Charles University and Humboldt University in Berlin.</blockquote>

Scientists reveal when chemical bonds form in molecular collisions 

We are delighted to invite food scientists from academia and industry, representatives of (inter)national agencies, control authorities, governmental and commercial laboratories to attend <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/events/928">RAFA 2026</a> (12th Symposium on Recent Advances in Food Analysis), that takes place 3–6 November 2026 in Prague..<blockquote>👉<a target="_blank" rel="noopener noreferrer" href="https://rafa.easyevent.eu/tickets/">SUBMIT ABSTRACT</a> FOR POSTER PRESENTATION by August 31, 2026Do not miss the opportunity to present your latest results at RAFA 2026.</blockquote><h5>Next deadlines:</h5><ul><li>August 31, 2026: 2nd window – &nbsp;<a target="_blank" rel="noopener noreferrer" href="https://www.rafa2026.eu/sponsors_exhibitors_media_partners_info.html">Application for participation as a Sponsor or Exhibitor</a></li><li>September 30, 2026:&nbsp;<ul><li><a target="_blank" rel="noopener noreferrer" href="https://www.rafa2026.eu/registration.html">Registration at the regular rate</a></li><li>Abstract submission – Last minute posters (May not appear in the RAFA 2026 program)</li></ul></li></ul>Since its first edition in 2003, RAFA has grown into a prestigious international event, typically welcoming up to 850 participants from more than 60 countries worldwide, with the support of more than 50 sponsors, exhibitors, media and supporting partners.RAFA 2026 will provide an overview of contemporary trends in the ANALYTICAL &amp; BIOANALYTICAL STRATEGIES IN FOOD QUALITY AND SAFETY CONTROL and discuss the CHALLENGES AND NOVEL APPROACHES IN FOOD AND NATURAL PRODUCTS ANALYSIS.View the <a target="_blank" rel="noopener noreferrer" href="https://www.rafa2026.eu/invited_speakers.html">list of distinguished speakers</a> who have accepted our invitation to RAFA 2026 and will present current hot topics and future perspectives in food analysis!<blockquote>👉More details on the <a target="_blank" rel="noopener noreferrer" href="https://www.rafa2026.eu/scientific_programme.html">RAFA 2026 preliminary program</a> can be found HERE.👉OUR <a target="_blank" rel="noopener noreferrer" href="https://www.rafa2026.eu/about_sponsors_exhibitors_partners.html">SPONSORS, EXHIBITORS, MEDIA and SUPPORTING PARTNERS</a></blockquote>You are kindly invited to join and contribute to our exciting scientific program and unforgettable social events!We look forward to meeting you again in Prague!<ul><li>Prof. Jana Pulkrabova &amp; Dr. Stefan van Leeuwen, Symposium Chairs</li><li>Prof. Michele Suman, Symposium Co-chair</li><li>Prof. Jana Hajslova &amp; Prof. Michel Nielen, Symposium Honorary Chairs</li></ul>

RAFA 2026 - Deadline for Abstract Submission for poster presentation is coming

Our Library never stops expanding. What are the most recent contributions to LabRulezICPMS Library in the week of 17th August 2026? Check out new documents from the field of spectroscopy/spectrometry and related techniques!<blockquote>👉 <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library">SEARCH THE LARGEST REPOSITORY OF DOCUMENTS ABOUT SPECTROSCOPY/SPECTROMETRY RELATED TECHNIQUES</a></blockquote><blockquote>👉 Need info about different analytical techniques? Peek into <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library">LabRulezLCMS</a> or <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library">LabRulezGCMS</a> libraries.</blockquote>This week we bring you application notes by Agilent Technologies, Metrohm, and Shimadzu and other document by Thermo Fisher Scientific!<h3>1. Agilent Technologies: Direct Analysis of Seawater Using ICP-QQQ and Integrated Advanced Valve System</h3>Fast, robust environmental analyses using an <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library?mainauthorItems=10&amp;search=9500">Agilent 9500 ICP-QQQ</a> with AVS MS&nbsp;<ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_seawater_9500_icp_qqq_5994_8988en_agilent_e56319c80a.pdf">Full PDF for download</a>&nbsp;</li></ul>Trace elements in seawater play a vital role in marine biogeochemical cycles, influencing ocean productivity, ecosystem health, and global climate regulation.1,2 Although present at extremely low concentrations, many trace elements are essential for biological processes, while others, including heavy metals, serve as indicators of contamination from industrial activities and coastal development. Accurate determination of a wide range of elements is therefore critical for environmental monitoring, oceanographic research, and regulatory compliance. EPA Method 200.8 provides a widely adopted quality control (QC) framework for trace metal analysis in natural waters.3 However, seawater’s high salinity and major components such as Na, Mg, Cl, and S create analytical challenges for conventional ICP-MS analysis, including ionization suppression and polyatomic interferences, such as ArCl+ on As, ArNa+ on Cu, SO2 + on Zn. Overcoming these issues requires advanced interference removal techniques and high sensitivity. Triple quadrupole ICP-MS (ICP-QQQ) addresses these limitations through its MS/MS configuration.Agilent ICP-MS/MS methods precisely control reaction chemistry and eliminate interferences, ensuring accurate quantification in complex saline matrices.&nbsp;The Agilent 9500 Triple Quadrupole ICP-MS with its unique Dual-Cell System (DCS) enables accurate, efficient seawater analysis using enhanced collision/reaction cell (CRC) technologies. Its performance is primarily driven by Advanced Helium Mode (AHM). This advanced collision mode delivers exceptional on-mass interference removal using a combination of Kinetic Energy Discrimination (KED) and Collision Induced Dissociation (CID), ensuring precise quantification even in highly saline and complex matrices.4 Additionally, Air cell mode enables fast, effective mass-shift reactions, adding flexibility for overcoming challenging interferences.5 By seamlessly integrating AHM with Air cell mode, the 9500 simplifies workflows and delivers reliable results for trace analysis of multiple elements in seawater.&nbsp;In this study, a <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library?mainauthorItems=10&amp;search=9500">9500 ICP-QQQ</a> fitted with the AVS MS was used to quantify 26 elements in two seawater certified reference materials (CRMs) and a sample collected in Singapore, employing an online reverse-dilution approach. The method was assessed following the performance requirements of EPA Method 200.8.<h4>Conclusion&nbsp;</h4>Traditional seawater analysis by ICP‑MS often requires extensive sample preparation, such as dilution and matrix separation, to address high salinity and complex matrix effects. These additional steps increase both turnaround time and contamination risk. The method developed here enables direct seawater analysis using an online reverse-dilution approach, eliminating manual preparation and enabling rapid, high-throughput processing. Using the Agilent 9500 ICP-QQQ with AVS MS in online dilution mode, the workflow achieved ppt-level MDLs for 26 elements, excellent accuracy (90–110% recoveries for CRMs and spiked samples), and long-term stability across more than 130 analyses, meeting EPA Method 200.8 QC requirements.&nbsp;Key advantages of the 9500 ICP-QQQ method:&nbsp;<ul><li>Effective interference removal: Advanced gas modes (AHM and Air cell mode) controlled polyatomic species originating from the high-salinity matrices.&nbsp;</li><li>High throughput: Automated online dilution and seamless gas-switching enabled complete analysis in 140 seconds per sample.&nbsp;</li><li>Robust stability: Optimized rinse protocols ensured consistent ISTD recovery and instrument performance over a seven-hour run comprising 100 injections of undiluted seawater samples.&nbsp;</li></ul>This workflow delivers fast, reliable, and high-quality seawater analysis, making it ideal for environmental monitoring and marine research laboratories seeking maximum efficiency without compromising data integrity.<h3>2. Metrohm: Moisture and protein content in corn starch with NIR spectroscopy</h3>Easily measure the quality of corn starch in seconds with NIR<ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_nir_151_download_087f0d33e0.pdf">Full PDF for download</a></li></ul>Starch is a fundamental component in candy production where it is often used as a gelling agent and thickener. The confectionery industry uses it to create products with a certain consistency, like pie fillings. It is also used in a process known as starch molding where shapes are pressed into a corn starch bed for gummy candies and similar treats. Corn starch also acts as a desiccant during the candies' drying process before reuse. Therefore, the corn starch moisture content is a very important factor to consider in this process.&nbsp;Near-infrared spectroscopy (NIRS) is a fast, chemicalfree analysis technique for the determination of moisture content and corn protein content in corn starch. The NIRS solution is easy to use and can be used either atline or in a quality control laboratory.<h4>EXPERIMENTAL EQUIPMENT&nbsp;</h4>210 samples of corn starch were measured with an <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library?mainauthorItems=220&amp;search=OMNIS+NIR">OMNIS NIR Analyzer Solid</a> (Figure 1). All measurements were performed in reflection mode (1000–2250 nm) using a large holder and large cup (Table 1). OMNIS Software was used for all data acquisition and prediction model development. Karl Fischer titration was used to determine the water content in corn starch, and the Kjeldahl method was used to determine its protein content.<h4>CONCLUSION</h4>This Application Note shows the feasibility of using near-infrared spectroscopy for the determination of moisture and protein content in corn starch. Compared to the conventional analysis techniques used to determine these quality parameters, NIRS saves a considerable amount of time and costs. With NIR spectroscopy, analyses can be conducted without using any chemical reagents, giving users reliable results in seconds.<h3>3. Shimadzu: Observation of Crack Propagation Process in Aluminum Alloy Specimen Using Air-Servo Microfocus X-Ray CT System</h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_01_01152_en_de411e6e13.pdf">Full PDF for download</a></li></ul><h5>User benefits</h5><ul><li>The Air-Servo Microfocus X-Ray CT System enables observation of crack propagation in three dimensions and over time.</li><li>Microfocus X-Ray CT system enables nondestructive observation of the interior of materials.</li><li>High-precision dynamic control is possible with the Servo Controller 4830.</li></ul>Many structural failures are caused by fatigue failure resulting from repeated loading. In fatigue failure, cracks initiate from microdefects in the material, internal voids, inclusions, and other features, and then propagate under repeated loading until final fracture occurs. To evaluate this sequence of processes, it is effective to observe defects and crack propagation nondestructively.&nbsp;Traditionally, crack observation has focused on visual inspection and microscopic observation, but these methods are limited to information near the surface. To sufficiently capture the threedimensional shape and changes in cracks propagating inside a material, observation of the fractured specimen after failure has generally been used. In contrast, X-ray CT can nondestructively visualize internal defects and cracks in three dimensions, making it possible to evaluate in detail changes in crack morphology, including in the interior.&nbsp;Accordingly, using the “Air-Servo Microfocus X-Ray CT System,” which combines X-ray CT with a fatigue testing machine, repeated tests were performed in which loading was stopped at fixed cycle intervals and imaging was carried out. This article introduces the resulting process of crack initiation and propagation in the same specimen.<h4>Conclusion</h4>Using the Air-Servo Microfocus X-Ray CT System, cracks propagating from the notch region of an aluminum alloy specimen were observed. First, static tests and fatigue tests were performed using the servo pulser EHF-LV, and a S-N diagram was obtained. Based on the obtained S-N diagram, the fatigue test conditions for the Air-Servo Microfocus X-Ray CT System were determined, and X-ray CT imaging was performed. The process of crack propagation according to the number of cycles was observed in cross-sectional images and 3D images. In addition, by visualizing the displacement from a specific cycle onward, it was also confirmed that the specimen necked down just before fracture.&nbsp;Using the measurement system introduced in this article, it is possible to observe changes in specimen shape over time while the specimen remains mounted in the jig. Therefore, not only the crack propagation process of a specimen during fatigue testing, but also material deformation behavior and the process of shape change can be observed.<h3>4. Thermo Fisher Scientific: IonicX Portable XRF Analyzer Device and Algorithm</h3>A detailed look into the algorithm used to authenticate ionic salts<ul><li>Other document</li><li><a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/labrulez-bucket-strapi-h3hsga3/ionicx_portable_xrf_analyzer_device_and_algorithm_an1649_en_6ffee8a584.pdf">Full PDF for download</a></li></ul>The <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/products/2026">Thermo Scientific™ IonicX™ Portable XRF Analyzer</a> utilizes Energy Dispersive X-ray Fluorescence (ED XRF) spectrometry to confidently differentiate between different chemical samples based on their atomic structure and the average atomic weight of the sample. The basic elements of XRF spectrometer systems include a radiation source, a sample, and an X-ray detector. The analysis relies on the interaction of radiation source output (an X-ray source) with a sample, in this case, the cup of ionic salt material, such as Sodium Chloride, Potassium Chloride, Sodium Hydroxide or other chemicals and salts. The XRF system can characterize materials, due to the fundamental principle that each element has a unique atomic structure, which in turn has a unique set of peaks (x-ray lines) in its emission spectrum. The energy dispersive X-ray detector separates (disperses) the detected radiation emitted from the sample by energy, thus providing a spectrum from which the different elements present in the sample can be identified and/ or quantified.<h4>Algorithm&nbsp;</h4>Handheld XRF devices often cannot detect elements lighter than Magnesium by their fluorescence lines, however many compounds contain elements of interest such as Oxygen and Hydrogen. Additionally, relying solely on primary fluorescence peaks to identify target compounds can lead to misinterpretation. For instance, if MgO and NaCl are present in a 1:1 mixture, the resulting XRF spectrum would display distinct characteristic Mg and Cl peaks. However, the sample would not actually be the spectrum of MgCl₂, as the analytical response of Mg and Cl would be very different in both samples because of a dilution effect and absorption from Na and O atoms. The XRF process can easily differentiate samples with similar elemental constituents but with different chemical structures by analyzing the resulting scatter from the sample and comparing the full spectrum to a calibration library of compounds. Figure 4 shows XRF spectra of Sodium Chlorate (NaClO₃) and Sodium Perchlorate (NaClO₄) taken with the IonicX XRF instrument. In this example, only the Cl fluorescence peak can be detected by the IonicX device as Na and O fluorescence X-rays have energies that are too weak to be detected. However, when the spectrum is normalized, in this case to the primary Compton peak of Ag Kα, a slight but distinguishable difference can be seen in the spectral intensity between the energies of 25 keV and 40 keV. The difference in the scatter of the X-ray tube Bremsstrahlung is caused by differences in mass absorption coefficients of the presented samples, in this case it is the extra O atom in the NaClO₄ molecule vs the NaClO₃ molecule.<h4>Summary&nbsp;</h4>The IonicX Portable XRF Analyzer is a powerful addition for the verification of ionic salt type chemicals, utilizing XRF technology in a versatile, easy to use, small form factor. IonicX provides clear, easy to understand, unambiguous results and tools to assist with compliance and data integrity. IonicX is a robust verification tool which allows pharmaceutical companies to more efficiently verify incoming chemicals that typically have been tested using lengthy wet-chemistry techniques.

News from LabRulezICPMS Library - Week 34, 2026

Article

Events

Application

Food

Science and research

RAFA provides an overview of contemporary trends in ANALYTICAL & BIOANALYTICAL STRATEGIES IN FOOD QUALITY AND SAFETY CONTROL and discusses CHALLENGES / NOVEL APPROACHES IN FOOD AND NATURAL PRODUCTS ANALYSIS.

Recent Advances in Food Analysis (RAFA)

Everything from the world of analytical chemistry in one place. We connect people in solving their problems. At Labrulez you will find all the necessary information easily, quickly and clearly. Stop searching and start finding.

LabRulez

Palacký University Olomouc (UP) is an internationally respected and scientifically and academically highly productive university in Central Europe. Founded 22 December 1573, it is the second-oldest university in the Czech Republic and the oldest one in Moravia. For 450 years it has contributed to the intellectual wealth of society and to its scientific, cultural, and social development.

Palacký University Olomouc

New Food magazine

Have you fully exploited the potential of your analytical techniques in edible oil analysis? Our experts will reveal what you can achieve with CNSX-analysis, ICP-OES, AAS and UV/Vis in regulated standard analysis and beyond.
Price fluctuations, supply bottlenecks and export stops have highlighted in recent years how volatile and complex the supply chains of edible oils are. Exporters, importers and processors of edible oils face the challenges of rapid supplier qualification while achieving regulatory compliant, seamless, and efficient quality monitoring of their crude oil, intermediates and final products.
As agricultural products, edible oils are subject to natural quality fluctuations, while cultivation methods and long transport routes pose risks of contamination and oxidation. In addition, they go through a temperature- and additive-intensive process with the refinery, during which undesirable by-products can arise under certain circumstances.
Our webinar is aimed at industry, regulatory and contract laboratories involved in the analysis of edible oils. With combustion elemental analysis, ICP-OES, AAS and UV/Vis molecular spectroscopy, our experts will introduce four techniques which enable precise, efficient, and standard-compliant quality and process analysis of edible oils. They will also show you tips and tricks on how to exploit the additional potential for optimising your analytical workflows regarding the targeted and economic use of elaborate specific techniques.
Learn how to use these techniques for a variety of oils at different steps in the value and processing chain, and how to achieve optimal results and increase sample throughput.
Key learning points:
<ul>
<li>Explore how to carry out the comprehensive analysis of toxic elements, process inhibitors, catalyst poisons as well as the macro-mineral content with ICP-OES.
</li>
<li>Learn what combustion analysis can achieve in quality control and process monitoring, especially regarding the formation of unwanted compounds during refining.
</li>
<li>Discover how to streamline analytical workflows with quick screens for organic and inorganic Sulfur and Nitrogen as sum parameters with combustion analysis.
</li>
<li>Find out how to assess oxidation in oils via DOBI index, and how to monitor the efficiency of bleaching in refinery using UV/Vis spectrometry.
</li>
<li>Discover what AAS can do as an alternative spectrometric element technique in the analysis of edible oils.
</li>
<li>Meet our experts and discuss with us in the Q&amp;A.
</li>
</ul>
<blockquote>
Presenter: Dr. Angela Gröbel (Senior Product Manager / Expert Supervisor Chemical Analysis)
</blockquote>
<blockquote>
Angela is a Senior Product Manager and Expert Supervisor for the combustion elemental analysis and related sample preparation portfolio. She holds a PhD in analytical chemistry. Angela developed Analytik Jena’s first trace elemental analysis product line for organic matter, later she became an expert in determination of Sulfur, Nitrogen, and Chlorine across a broad range of industry segments, including oil and gas, food and agriculture and environmental protection. Since 2013 Angela has been Product Manager, responsible for the entire combustion elemental analysis and related sample preparation portfolio.
</blockquote>
<blockquote>
Presenter: Dr. Holger Sievers (Application Specialist Chemical Analysis)
</blockquote>
<blockquote>
Holger Sievers is an Application Specialist at Analytik Jena. He holds a PhD from the Technical University of Munich in the field of ultra-trace analysis of noble metals which he obtained after his Master’s focusing on inorganic and analytical chemistry. Holger joined Analytik Jena in 2018 after seven years of teaching at the University and is currently engaged in chemical analysis. His primary focus lies in atomic absorption spectrometry and element analysis in general.
</blockquote>
<blockquote>
Presenter: Sandra Wunsch (Application Specialist Chemical Analysis)
</blockquote>
<blockquote>
Sandra Wunsch has been an Application Specialist for molecular spectrometry at Analytik Jena since 2016. She has intense in-depth knowledge in scientific and industrial application of molecular spectrometry, and extensive experience in the market and application fields, especially in the areas of environment and food &amp; agriculture. As a graduated Nutritionist, she is an expert in the use of chemical analysis and especially the determination of molecular compounds in the food industry and related fields.
</blockquote>

New Food: Edible oil processing: How to monitor elements and compounds

Edible oil processing: How to monitor elements and compounds

How to use these techniques for a variety of oils at different steps in the value and processing chain, and how to achieve optimal results.

ICPMS webinars focusing on UV-Vis - page 1

Edible oil processing: How to monitor elements and compounds

Related content

Scientists reveal when chemical bonds form in molecular collisions

News from LabRulezICPMS Library - Week 34, 2026

RAFA 2026 - Deadline for Abstract Submission for poster presentation is coming